Products
NEWS DETAILS
Home > News >
How We Confirm a Spray Booth Fits Before Production
Events
Contact Us
Mr. Tim
86--18981189424
WeChat +86 189 8118 9424
Contact Now

How We Confirm a Spray Booth Fits Before Production

2026-11-16
Latest company news about How We Confirm a Spray Booth Fits Before Production

A Question from Algeria: How CoatTech Confirms a Spray Booth Will Fit Before Production Starts

News · CoatTech Guidance Series

In November 2026, a car refinishing workshop in Algeria asked CoatTech a question that had nothing to do with price: would a spray booth actually fit inside a garage approximately 8.5 m long, 4.0 m wide and 3.0 m high, and what were the exact external and internal dimensions? The client name and all commercial terms are withheld.

As enquiry volume stays high through the fourth quarter, this is the question that comes up more often than any price discussion — and a buyer can compare quotations for weeks only to discover at installation that the ceiling plenum, the air handling unit or the door arrangement was never accounted for.

CoatTech has therefore made dimensional confirmation a formal step before any booth is released to fabrication, rather than a check left until delivery. If a building cannot accommodate the booth, we say so before fabrication: a lower-profile configuration, a different air unit position or a recessed pit may solve it, and sometimes the honest answer is that the building needs a different approach. That answer is more useful before fabrication than after delivery.

The fit-confirmation sequence

Step

What is recorded

Who confirms

1. Site dimensions

Measured length, width and clear height at the lowest point, plus beams, sprinklers, roof trusses and obstructions

Client supplies the measured layout or hosts the survey

2. Internal and external envelope

A general arrangement drawing states both figures, so the working space and the full equipment footprint are seen separately

CoatTech issues the drawing

3. Air unit position

Side, rear or top-mounted units have different footprints; the position is agreed, not assumed

Agreed in writing on the drawing

4. Floor arrangement

Where ceiling height is tight, a recessed pit can gain working height downward instead of raising the roof

CoatTech advises; client confirms excavation is permitted

5. Drawing approval and freeze

Dimensions, airflow and connected load are frozen, with written client approval of the general arrangement

Client signs; CoatTech releases to fabrication

6. Pre-installation recheck

The site is re-verified against the approved drawing before the equipment ships

CoatTech, before dispatch

 

Why we publish the sequence

A published process is easier for a buyer to check than a promise. It also means every quotation, drawing and technical guide on this site uses the same rule: state the number, have it confirmed, and freeze it.

What this means for buyers

If you are planning a workshop, the most useful thing you can send at enquiry stage is not a target booth size. It is your building dimensions, a few site photos showing the ceiling and any obstructions, the largest vehicle you intend to paint, and whether excavation is permitted. From that, an accurate layout can be produced before any commercial discussion.

The two questions most often asked alongside "will it fit" are answered in full in the guides below: how the internal and external envelopes are calculated, and how the filtration stages are specified and replaced over the life of the booth. Both apply the same rule as the sequence above — the numbers are stated, checked and frozen rather than adjusted later to make the equipment fit.

Part of the CoatTech Guidance Series

This note is the hub for two technical guides from the same November 2026 enquiry:

· Spray Booth Dimensions Explained: Internal vs External, Minimum Garage Requirements, and the Recessed Pit Option — where the height goes, what an 8.5 × 4.0 × 3.0 m garage realistically yields, and when a recessed pit is the right answer.

· Spray Booth Filter Replacement: Intervals, What Can Be Cleaned, and What a Complete Set Includes — indicative replacement intervals, the replace-only rule, and what one full changeover contains.

All three came out of the same kind of question a buyer asks before placing an order. CoatTech designs and builds custom spray booths, pretreatment lines and curing ovens for industrial and automotive finishing operations worldwide.

Talk to our engineering team

Send us your building dimensions, a few site photos showing the ceiling and any obstructions, the largest vehicle you intend to paint, and whether excavation is permitted. We will produce an accurate layout before any commercial discussion — including an honest answer if your building cannot accommodate the booth you have in mind.

Products
NEWS DETAILS
How We Confirm a Spray Booth Fits Before Production
2026-11-16
Latest company news about How We Confirm a Spray Booth Fits Before Production

A Question from Algeria: How CoatTech Confirms a Spray Booth Will Fit Before Production Starts

News · CoatTech Guidance Series

In November 2026, a car refinishing workshop in Algeria asked CoatTech a question that had nothing to do with price: would a spray booth actually fit inside a garage approximately 8.5 m long, 4.0 m wide and 3.0 m high, and what were the exact external and internal dimensions? The client name and all commercial terms are withheld.

As enquiry volume stays high through the fourth quarter, this is the question that comes up more often than any price discussion — and a buyer can compare quotations for weeks only to discover at installation that the ceiling plenum, the air handling unit or the door arrangement was never accounted for.

CoatTech has therefore made dimensional confirmation a formal step before any booth is released to fabrication, rather than a check left until delivery. If a building cannot accommodate the booth, we say so before fabrication: a lower-profile configuration, a different air unit position or a recessed pit may solve it, and sometimes the honest answer is that the building needs a different approach. That answer is more useful before fabrication than after delivery.

The fit-confirmation sequence

Step

What is recorded

Who confirms

1. Site dimensions

Measured length, width and clear height at the lowest point, plus beams, sprinklers, roof trusses and obstructions

Client supplies the measured layout or hosts the survey

2. Internal and external envelope

A general arrangement drawing states both figures, so the working space and the full equipment footprint are seen separately

CoatTech issues the drawing

3. Air unit position

Side, rear or top-mounted units have different footprints; the position is agreed, not assumed

Agreed in writing on the drawing

4. Floor arrangement

Where ceiling height is tight, a recessed pit can gain working height downward instead of raising the roof

CoatTech advises; client confirms excavation is permitted

5. Drawing approval and freeze

Dimensions, airflow and connected load are frozen, with written client approval of the general arrangement

Client signs; CoatTech releases to fabrication

6. Pre-installation recheck

The site is re-verified against the approved drawing before the equipment ships

CoatTech, before dispatch

 

Why we publish the sequence

A published process is easier for a buyer to check than a promise. It also means every quotation, drawing and technical guide on this site uses the same rule: state the number, have it confirmed, and freeze it.

What this means for buyers

If you are planning a workshop, the most useful thing you can send at enquiry stage is not a target booth size. It is your building dimensions, a few site photos showing the ceiling and any obstructions, the largest vehicle you intend to paint, and whether excavation is permitted. From that, an accurate layout can be produced before any commercial discussion.

The two questions most often asked alongside "will it fit" are answered in full in the guides below: how the internal and external envelopes are calculated, and how the filtration stages are specified and replaced over the life of the booth. Both apply the same rule as the sequence above — the numbers are stated, checked and frozen rather than adjusted later to make the equipment fit.

Part of the CoatTech Guidance Series

This note is the hub for two technical guides from the same November 2026 enquiry:

· Spray Booth Dimensions Explained: Internal vs External, Minimum Garage Requirements, and the Recessed Pit Option — where the height goes, what an 8.5 × 4.0 × 3.0 m garage realistically yields, and when a recessed pit is the right answer.

· Spray Booth Filter Replacement: Intervals, What Can Be Cleaned, and What a Complete Set Includes — indicative replacement intervals, the replace-only rule, and what one full changeover contains.

All three came out of the same kind of question a buyer asks before placing an order. CoatTech designs and builds custom spray booths, pretreatment lines and curing ovens for industrial and automotive finishing operations worldwide.

Talk to our engineering team

Send us your building dimensions, a few site photos showing the ceiling and any obstructions, the largest vehicle you intend to paint, and whether excavation is permitted. We will produce an accurate layout before any commercial discussion — including an honest answer if your building cannot accommodate the booth you have in mind.

sitemap |  Privacy Policy | China Good Quality Spray Booth Supplier. Copyright © 2024-2026 CoatTech Intelligent Equipment(Guangzhou) CO.,LTD . All Rights Reserved.